Home         Products     Software    Contact           Links Documentation
Products
5C Rotary table- Fanuc and Fadal compatible 5C rotary table.

5C rotary table with servo kits for Fadal and Fanuc CNC's. Built from top-quality components and engineered to provide robust operation without sacrificing accuracy. Its heat treated steel gear set uses throated helix gears for greater contact area to reduce gear wear and absorb shock loads. A dual adjustment design provides optimal gear mesh to further enhance the performance and accuracy of the gear set. AC brushless motors used in the 5C eliminates any maintenance
associated with  brush replacement.

       - Standard manual collect closer  

       -Optional air collet closer

       - Optional tail stocks available             

                                                                       >> click for more info

USBCNC- Universal USB controller for CNC's with serial port. (Fanuc, Fadal, Haas, Siemens,.....)

The USBCNC disk reader control acts as an interface between commercially available USB flash memory and any CNC control with an available RS-232 port. Machine tool files can be sent from CNC memory to the USB key, USB key to CNC memory or drip fed (DNC) from the USB key. Flexible DNC firmware is built into the USBCNC unit allowing connection to just about any machine tool CNC
control. No hardware or software upgrades are required on the machine. Included with controller purchase:

       - 1 GB USB flash key                                    -Modular serial cable

       - Wall plug power supply                          

       - Modular Male and Female DB25 serial port connectors

        >> click for more info

USBCNC                   $750.00
Universal USB to CNC controller. Portable version with 1 GB USB key, power supply
and serial cable with DB25 male and female connectors.
USBCNC- Internal/Pendant mount Universal USB controller for CNC's with serial port.
(Fanuc, Fadal, Haas, Siemens,.....)

The USBCNC-INT kit allows a USB controller to mounted on the pendant of the machine tool. When installed, the internal version of the USB controller becomes an integral part of the machine tool pendant. An aluminum anodized drill jig/bezel makes mounting of the USBCNC display an easy process. Typical installation time should take less than 40 minutes. No hardware or software
upgrades are required on the machine. Included with controller purchase:

- 1 GB USB flash key                 - Modular serial cable w/DB25 connector

- Power cable, USB cable, water proof panel mount USB connector

- USB controller w/DIN rail     - anodized aluminum display bezel & display

  >> click for more info

USBCNC-INT                   $650.00

Universal USB to CNC controller. Pendant mount version with 1 GB USB key, keypad,
 panel mount USB connector and all power/serial cables required for installation.

LANCNC-FAD Ethernet controller for Fadal CNC 88


The LANCNC-FAD controller adds data server capability to any Fadal CNC.
 No special software is required. Simply drag and drop files on your
 network to the data server located in the machine's control cabinet.
Files can be accessed by the CNC independently from the network
insuring operation even when a network is down. Files too large to fit on resident CNC memory can be drip fed via DNC. Files can be updated
without the network if required by removing the SD card and updating
at a PC. A 1 GB SD card is provided as standard. The unit is compatible
with standard wireless routers.  

>> click for more info

LANCNC-FAD                   $600.00
Internal mount Fadal CNC88 Ethernet controller. Includes P/S cable & 1 GB SD card.

USBCNC-FAD USB controller for Fadal CNC 88
USB flash key reader controller that acts an interface between commercially available USB flash memory and any version of Fadal CNC88 controller. The USBCNC-FAD controller accepts keypad
input commands from the Fadal control pendant. A help menu provides program as well as tooling information to be stored or loaded between the CNC memory and a USB key. Machine parameters
can also be stored for easy loading during machine maintenance. No hardware or software
upgrades are required on the machine. Included with controller purchase:

       - 1 GB USB flash key                                    -25 foot DB25 cable

       - Wall plug regulated 5V power supply

      - Machine magnet with printed command set

                                                            >> click for more info

USBCNC-FAD                   $650.00
External mount Fadal CNC88 USB controller. Includes power supply, 1 GB USB key and
25 foot serial cable.

USBCNC-FAD-INT             $550.00
Pendant mount Fadal CNC88 USB controller. Includes cables for pendant mounting,
waterproof panel mount USB connector, power plug to CNC 5V supply, & 1 GB USB key.

USBCNC-FAD-SW USB controller for Fadal CNC 88 with network switch pass though
USB flash key reader controller that acts an interface between commercially available USB flash memory and any version of Fadal CNC88 controller. The USBCNC-FAD-SW controller accepts keypad
input commands from the Fadal control pendant and allows connection with a remote PC as well. Auto-sensing circuit connects PC or USB to the CNC without physically changing network cables or connections . Included with controller purchase:
       - 1 GB USB flash key                            -15 foot USB cable

       - Panel mount USB plug                      - Power supply cable

>> click for more info

USBCNC-FAD-SW                   $600.00
USBCNC controller for Fadal CNC's with automatic serial switchbox feature.

Our online ordering system is handled through PayPal. PayPal, an Ebay company, is a global leader in online transactions
and maintains a safe and secure site. Once your cart is complete, you will be automatically redirected to a PayPal site where
 your credit information can be entered. If you do not have a PayPal account, continue through the order entry system
and a choice to use MasterCard, AMEX, Visa, or Discover will become available. 



MC104P PC104 controller

MC104P controller - Embedded PIC18F8722 from Microchip packaged in a PC/104 form factor controller. Use as a standalone controller or add PC/104 I/O expansion
 boards as needed for your application.  (PC/104 drives, high resolution analog modules, communication, motion control cards,..... )                 

       - 128K Flash Memory                                    -132K SRAM

       - 1K EEPROM                                                   -40MHZ Clock

       - Full PC/104 I/O addressing capability  -ICD2 connector

       -2 Serial Ports (1 RS-232/RS-485, 1 RS-232)

- 4 Analog Inputs 0-5V, 10 bits     - 8 Digital Outputs, Open Collector 40V/400mA                       

- 8 Digital Inputs (4 tied to high speed interrupts or IRQ lines)

MC104P                 $99.00
Microcontroller in PC104 form factor

MC104P-XP            $109.00
MC104P in PC104 form factor with extended pins for stack-through operation.

DC104 Drives

Brushed DC motor controllers in an industry standard PC/104 form factor. Access and control all parameters across an open standard PC/104 bus. Units available in 2, 5 and 10 amps. DC104 drives are available in reversing and non-reversing models. An optional encoder feedback option can be added for improved speed regulation and position tracking with quadrature encoders.

DC104NR-2A               $279.00
 Non-reversing 2 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
DC104NR-2A-ENC        $309.00
 Non-reversing 2 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DC104-2A                    $299.00
 Reversing 4 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
DC104-2A-ENC             $329.00
 Reversing 4 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DC104NR-5A                $329.00
Non-reversing 2 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
DC104NR-5A-ENC         $359.00
 Non-reversing 2 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DC104-5A                     $349.00
 Reversing 4 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
DC104-5A-ENC              $379.00
 Reversing 4 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
DC104NR-10A               $379.00
 Non-reversing 2 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
DC104NR-10A-ENC       $409.00
 Non-reversing 2 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
Includes encoder feedback
DC104-10A                   $399.00
 Reversing 4 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
DC104-10A-ENC            $429.00
 Reversing 4 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
Includes encoder feedback
 

Serial DC Drives

Brushed DC motor controllers with serial input control. Access and control all parameters via RS-232 serial port. Units available in 2, 5 and 10 amps. Serial DC drives are available in reversing and non-reversing models. An optional encoder feedback option can be added for improved speed regulation and position tracking with quadrature encoders.

DCNR-2A-SER                $149.00
 Non-reversing 2 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DCNR-2A-SER-ENC        $179.00
 Non-reversing 2 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DC-2A-SER                    $169.00
 Reversing 4 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
DC-2A-SER-ENC             $199.00
 Reversing 4 quadrant operation. 2 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DCNR-5A-SER                $199.00
 Non-reversing 2 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
DCNR-5A-SER-ENC         $229.00
 Non-reversing 2 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DC-5A-SER                    $219.00
 Reversing 4 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
DC-5A-SER-ENC             $249.00
 Reversing 4 quadrant operation. 5 Amp output. 115/230 VAC input, 90/180 VDC output.
Includes encoder feedback
DCNR-10A-SER                $249.00
 Non-reversing 2 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
DCNR-10A-SER-ENC         $279.00
 Non-reversing 2 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
Includes encoder feedback
DC-10A-SER                    $269.00
 Reversing 4 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
DC-10A-SER-ENC             $299.00
 Reversing 4 quadrant operation. 10 Amp output. 115 VAC input, 90 VDC output.
Includes encoder feedback

Our online ordering system is handled through PayPal. PayPal, an Ebay company, is a global leader in online transactions and maintains a safe and secure site. Once your cart is complete, you will be automatically
redirected to a PayPal site where your credit information can be entered. If you do not have a PayPal account, continue through the order entry system and a choice to use MasterCard, AMEX, Visa, or Discover will become  available. 

Drive Accessories

Win Utility - Windows programming software and scope function. Program, load and save    parameters with this
easy to use tool. Auto-connects to your PC's serial port. Scope function makes drive and control loop tuning quick and simple.

Palm/104 - Palm based programming and monitoring software. Use any Palm OS device with  Universal Adapter to connect to your drive. Eliminates dedicated programming terminals .

TB-DC         $15.00
 Provides quick and easy field termination to a standard DIN rail with clearly marked connections.
DIN clips can be removed for non-DIN Rail mounting.
D10-DB9    $16.00
 10 PIN IDC to DB9 connector for connection to serial port only drives and/or software utilities.
USB-SER     $20.00
 USB to serial port converter.

 
Home  |   Products  |   Software  |   Contact   |   Links  |   Documentation Calmotion.Com © 2005